Hello, i want to control my motorized Laser Screen with Freestyler. I have a 3 Channel Relay Interface. Is it possible to Programm the 3 Channels so that only one Channel can be on? Because it is not good when the "up" function is on an the "down" is also on.
I Need it that the others channels will be set on "0" when a Channel is activated.
Channel 1 is up, Channel 2 is stop, Channel 3 is down.
Hallo, ich möchte meinen Lasergazemotorleinwand per Freestyler steuern.
Dazu müsste ich aber ein Fixture machen dass folgende Funktion hat.
3 Kanäle. (1 auf, 2 Stop, 3 ab)
Das ist so ja kein Problem.
Aber das Problem ist, dass wenn ein Kanal betätigt wird die anderen auf 0 Springen müssen da ja ein gleichzeitiges "auf" und "ab" betätigen den Motor kaputt macht.
Wäre schön wenn mir jemand ein Tipp geben könnte wie ich das mit dem Fixture Creator hinbekomme.
Motorized Screen for Laser Fixture
Forum rules
This forum is designed for you to get HELP with building fixtures, Please make an attempt if you get stuck YOU must upload your partial fixture file (as an exported fixture file) so we can point you in the right direction if you don't do this you won't LEARN and if you don't learn you will may never be able to get the fixtures you require. It is Very hard to make fixtures for people when we don't have the same light at hand to test it with after all having the light in front of you makes programing so much easier! That's why we will help but rarely build any fixtures for you. You Alone are the best person to build your fixtures if you need help ask if you want it building for you Don't....
or alternativaly if your willing to pay for fixtures to be created then go here : http://www.freestylersupport.com/wiki/f ... on_service
You can Upload your fixtures as attachments to your posts so there is no need to supply email details Please post any fixtures in the download forum if you require help please contact an Admin/Moderator.
This forum is designed for you to get HELP with building fixtures, Please make an attempt if you get stuck YOU must upload your partial fixture file (as an exported fixture file) so we can point you in the right direction if you don't do this you won't LEARN and if you don't learn you will may never be able to get the fixtures you require. It is Very hard to make fixtures for people when we don't have the same light at hand to test it with after all having the light in front of you makes programing so much easier! That's why we will help but rarely build any fixtures for you. You Alone are the best person to build your fixtures if you need help ask if you want it building for you Don't....
or alternativaly if your willing to pay for fixtures to be created then go here : http://www.freestylersupport.com/wiki/f ... on_service
You can Upload your fixtures as attachments to your posts so there is no need to supply email details Please post any fixtures in the download forum if you require help please contact an Admin/Moderator.
-
- Knows how to turn Lights ON
- Posts: 2
- Joined: August 26th, 2014, 9:57 am
-
- Moderator
- Posts: 768
- Joined: November 16th, 2016, 2:24 pm
- FreeStyler Version: 4.1.6
- I Use FreeStyler for: Stage Show
Re: Motorized Screen for Laser Fixture
One possibility is to use the macro function. A macro can set a value in multiple channels.
For example you could have 3 macros:
Macro A would set channel 1 to 255, channel 2 to 0 and channel 3 to 0
Macro B would set channel 1 to 0, channel 2 to 255 and channel 3 to 0
Macro C would set channel 1 to 0, channel 2 to 0 and channel 3 to 255.
If you are running live the values would be sent immediately
If you are running a sequence then the channels need to be set to SNAP, not FADE. Based on your comment that the engine could be damaged, the SNAP setting is critical. When you are programming a sequence and you select the fixture note the small icon on the right hand side of the Freestyler sliders. If it is a green triangle the the channel is set to FADE. If it is a yellow lightning bolt the channel is set to SNAP. It if is a red circle with a dash then the channel setting is not recorded in this step of the sequence and will not change when Freestyler runs that step of the sequence.
For example you could have 3 macros:
Macro A would set channel 1 to 255, channel 2 to 0 and channel 3 to 0
Macro B would set channel 1 to 0, channel 2 to 255 and channel 3 to 0
Macro C would set channel 1 to 0, channel 2 to 0 and channel 3 to 255.
If you are running live the values would be sent immediately
If you are running a sequence then the channels need to be set to SNAP, not FADE. Based on your comment that the engine could be damaged, the SNAP setting is critical. When you are programming a sequence and you select the fixture note the small icon on the right hand side of the Freestyler sliders. If it is a green triangle the the channel is set to FADE. If it is a yellow lightning bolt the channel is set to SNAP. It if is a red circle with a dash then the channel setting is not recorded in this step of the sequence and will not change when Freestyler runs that step of the sequence.
-
- Knows how to turn Lights ON
- Posts: 2
- Joined: August 26th, 2014, 9:57 am
Re: Motorized Screen for Laser Fixture
Perfect. Thanks. Works fine.